ProTek60 Pro O3 6S HD Cinelifter
SKU
About
Description
Highlights:
Protected Propellers for indoor and outdoor use, protecting whatever you might bump into from nasty cuts
DJI O3 HD Air Unit Low-Latency Digital Transmission with 4K Stabilized Video with 155° Ultra-Wide Angle
Universal camera mount and accessories for a wide range of cameras to install
Updated BLITZ E80 4-IN-1 ESC for more power and reliability
Big size XING2 3110 power motors with extreme lift and flight performance
BLITZ M10 GPS module pre-installed (BF GPS rescue or INAV GPS RTH feature available)
Camera Power Supply Module // IFlight Camera Power 12V 3A BEC Module Short-circuit Protection Function
Specifications:
Product Name: ProTek60 Pro O3
FC: BLITZ F7 Pro Flight Controller
ESC: BLITZ E80 4-IN-1 Pro ESC
Video Transmission: DJI O3 Air Unit
Frame: 282mm wheelbase
Motor: XING2 3110 1600KV motors
Prop: Nazgul 6x4x3 propellers
Weight：1466grams
Max Speed: 110 Km/H (Manual Mode)
Maximum Takeoff Altitude: 3200 m
Max Hover Time: Approx. 5.5 mins with 1.3KG load and 6S 4500mAh battery
Max Wind Speed Resistance: Level 6
Operating Temperature Range: -10° to 40° C (14° to 104° F)
Antennas: Dual Antennas
GNSS: GPS + Galileo
Video Transmission:
Product Name: DJI O3 Air Unit
Weight: Approx. 36.4 grams（headband included）
Communication Bandwidth: Max 40 MHz
FOV (single screen): 155°
Communication Frequency: 2.400-2.4835 GHz (RX only) / 5.725-5.850 GHz (RX and TX)
End-to-End Latency
With DJI FPV Goggles V2:
810p/120fps Video Transmission Quality: The latency is lower than 28 ms.
810p/60fps Video Transmission Quality: The latency is lower than 40 ms.
With DJI Goggles 2:
1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.
1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.
Max Video Transmission Bitrate: 50 Mbps
Max Video Transmission Range：10 km (FCC), 2 km (CE), 6 km (SRRC)
Operating Temperature Range: -10º to 40º C (14° to 104° F)
Power Input: 7.4-26.4 V
Audio Transmission: N/A
Packing List:
1 x ProTek60 Pro O3 BNF
1 x Nazgul 6x4x3 Propellers(Pairs)
2 x Albatross LHCP 5.8GHz SMA FPV Antenna
1 x XT90 Male to XT60 Female Adapter Wire
1 x Fullsend X 6S 5600mAh Battery
2 x Battery Strap
1 x XT90 Smart Smoke Stopper
1 x Prop Wrench
Notice:
All iFlight BNFs are tested before shipment to guarantee highest quality.
If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.
Characteristics
Size
6 inch
Geometry
Ducted
Flight Stack
BLITZ F7 Pro/E80
Motors
3110 1600KV
Video Transmitter
DJI O3 Air Unit
Radio Transmitter
DJI FPV RC2, ELRS, TBS (optional)
GPS Module
M10 chipset
Max. Speed
110 km/h
Weight
ca. 1466 (without battery)
Description
Highlights:
Protected Propellers for indoor and outdoor use, protecting whatever you might bump into from nasty cuts
DJI O3 HD Air Unit Low-Latency Digital Transmission with 4K Stabilized Video with 155° Ultra-Wide Angle
Universal camera mount and accessories for a wide range of cameras to install
Updated BLITZ E80 4-IN-1 ESC for more power and reliability
Big size XING2 3110 power motors with extreme lift and flight performance
BLITZ M10 GPS module pre-installed (BF GPS rescue or INAV GPS RTH feature available)
Camera Power Supply Module // IFlight Camera Power 12V 3A BEC Module Short-circuit Protection Function
Specifications:
Product Name: ProTek60 Pro O3
FC: BLITZ F7 Pro Flight Controller
ESC: BLITZ E80 4-IN-1 Pro ESC
Video Transmission: DJI O3 Air Unit
Frame: 282mm wheelbase
Motor: XING2 3110 1600KV motors
Prop: Nazgul 6x4x3 propellers
Weight：1466grams
Max Speed: 110 Km/H (Manual Mode)
Maximum Takeoff Altitude: 3200 m
Max Hover Time: Approx. 5.5 mins with 1.3KG load and 6S 4500mAh battery
Max Wind Speed Resistance: Level 6
Operating Temperature Range: -10° to 40° C (14° to 104° F)
Antennas: Dual Antennas
GNSS: GPS + Galileo
Video Transmission:
Product Name: DJI O3 Air Unit
Weight: Approx. 36.4 grams（headband included）
Communication Bandwidth: Max 40 MHz
FOV (single screen): 155°
Communication Frequency: 2.400-2.4835 GHz (RX only) / 5.725-5.850 GHz (RX and TX)
End-to-End Latency
With DJI FPV Goggles V2:
810p/120fps Video Transmission Quality: The latency is lower than 28 ms.
810p/60fps Video Transmission Quality: The latency is lower than 40 ms.
With DJI Goggles 2:
1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.
1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.
Max Video Transmission Bitrate: 50 Mbps
Max Video Transmission Range：10 km (FCC), 2 km (CE), 6 km (SRRC)
Operating Temperature Range: -10º to 40º C (14° to 104° F)
Power Input: 7.4-26.4 V
Audio Transmission: N/A
Packing List:
1 x ProTek60 Pro O3 BNF
1 x Nazgul 6x4x3 Propellers(Pairs)
2 x Albatross LHCP 5.8GHz SMA FPV Antenna
1 x XT90 Male to XT60 Female Adapter Wire
1 x Fullsend X 6S 5600mAh Battery
2 x Battery Strap
1 x XT90 Smart Smoke Stopper
1 x Prop Wrench
Notice:
All iFlight BNFs are tested before shipment to guarantee highest quality.
If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.
Characteristics
Size
6 inch
Geometry
Ducted
Flight Stack
BLITZ F7 Pro/E80
Motors
3110 1600KV
Video Transmitter
DJI O3 Air Unit
Radio Transmitter
DJI FPV RC2, ELRS, TBS (optional)
GPS Module
M10 chipset
Max. Speed
110 km/h
Weight
ca. 1466 (without battery)
Описание
Highlights:
- Protected Propellers for indoor and outdoor use, protecting whatever you might bump into from nasty cuts
- DJI O3 HD Air Unit Low-Latency Digital Transmission with 4K Stabilized Video with 155° Ultra-Wide Angle
- Universal camera mount and accessories for a wide range of cameras to install
- Updated BLITZ E80 4-IN-1 ESC for more power and reliability
- Big size XING2 3110 power motors with extreme lift and flight performance
- BLITZ M10 GPS module pre-installed (BF GPS rescue or INAV GPS RTH feature available)
- Camera Power Supply Module // IFlight Camera Power 12V 3A BEC Module Short-circuit Protection Function
Specifications:
Product Name: ProTek60 Pro O3
FC: BLITZ F7 Pro Flight Controller
ESC: BLITZ E80 4-IN-1 Pro ESC
Video Transmission: DJI O3 Air Unit
Frame: 282mm wheelbase
Motor: XING2 3110 1600KV motors
Prop: Nazgul 6x4x3 propellers
Weight：1466grams
Max Speed: 110 Km/H (Manual Mode)
Maximum Takeoff Altitude: 3200 m
Max Hover Time: Approx. 5.5 mins with 1.3KG load and 6S 4500mAh battery
Max Wind Speed Resistance: Level 6
Operating Temperature Range: -10° to 40° C (14° to 104° F)
Antennas: Dual Antennas
GNSS: GPS + Galileo
Video Transmission:
Product Name: DJI O3 Air Unit
Weight: Approx. 36.4 grams（headband included）
Communication Bandwidth: Max 40 MHz
FOV (single screen): 155°
Communication Frequency: 2.400-2.4835 GHz (RX only) / 5.725-5.850 GHz (RX and TX)
End-to-End Latency
With DJI FPV Goggles V2:
810p/120fps Video Transmission Quality: The latency is lower than 28 ms.
810p/60fps Video Transmission Quality: The latency is lower than 40 ms.
With DJI Goggles 2:
1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.
1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.
Max Video Transmission Bitrate: 50 Mbps
Max Video Transmission Range：10 km (FCC), 2 km (CE), 6 km (SRRC)
Operating Temperature Range: -10º to 40º C (14° to 104° F)
Power Input: 7.4-26.4 V
Audio Transmission: N/A
Packing List:
1 x ProTek60 Pro O3 BNF
1 x Nazgul 6x4x3 Propellers(Pairs)
2 x Albatross LHCP 5.8GHz SMA FPV Antenna
1 x XT90 Male to XT60 Female Adapter Wire
1 x Fullsend X 6S 5600mAh Battery
2 x Battery Strap
1 x XT90 Smart Smoke Stopper
1 x Prop Wrench
Notice:
All iFlight BNFs are tested before shipment to guarantee highest quality.
If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.
