-
About Description The next generation of ESCs from iFlight has arrived. Currently used in BNF quads such as the Nazgul F5/F6 Series. These new 55Amp BLHeli32 BLITZ 4in1 ESCs can handle even the most amp-hungry motors. Powerful 55A for 2-6S batteries. 30,5x30,5 mounting pattern. The perfect match for the BLITZ Flight Controller series. Specifications: Mounting Holes: 30.5*30.5mm/Φ4mm Weight: 15.3g Supports 2-6S lipo input MCU：G071 Constant: 55 Amps Burst: 65 Amps Current sensor: Yes BEC: No Current rate: 200 Supports: DShot DShot150/300/600/MultiShot/ OneShot etc. Target: IFLIGHT_BLITZ_G2 Packing List: 1 x BLITZ E55 4-IN-1 2-6S ESC 1 x Power cables & ESC signal wires Description The next generation of ESCs from iFlight has arrived. Currently used in BNF quads such as the Nazgul F5/F6 Series. These new 55Amp BLHeli32 BLITZ 4in1 ESCs can handle even the most amp-hungry motors. Powerful 55A for 2-6S batteries. 30,5x30,5 mounting pattern. The perfect match for the BLITZ Flight Controller series. Specifications: Mounting Holes: 30.5*30.5mm/Φ4mm Weight: 15.3g Supports 2-6S lipo input MCU：G071 Constant: 55 Amps Burst: 65 Amps Current sensor: Yes BEC: No Current rate: 200 Supports: DShot DShot150/300/600/MultiShot/ OneShot etc. Target: IFLIGHT_BLITZ_G2 Packing List: 1 x BLITZ E55 4-IN-1 2-6S ESC 1 x Power cables & ESC signal wires -
About Description The next generation of ESCs from iFlight has arrived. These new 55Amp BLHeli32 BLITZ 4in1 ESCs can handle even the most amp-hungry motors. Lager Mosfets and bigger PCB for maximum heat dissipation. Powerful 55A for 2-6S batteries and 20x20 mounting pattern. The perfect match for the BLITZ Flight Controller series. Features: Larger MOSFET for more durable Better heat dissipation Safer with high redundancy Outstanding performance Specifications: Product Name: BLITZ E55R 4-IN-1 ESC (G2) Input Voltage: 2-6S Max. Continuous Current: 55A Max. Burst Current: 65A MCU: G071 BEC: No Firmware: BLHeli32 Current Sensor: Yes Current rate: 200 Telemetry: Supported Target: IFLIGHT_BLITZ_G2 Mounting Holes: 20 x20 mm/Φ4mm Weight: 15.3g Protocol: Supports DShot150/300/600/MultiShot/ OneShot etc. Compatibility: Mach R5 V1/Sport Frame kit AOS 5R Frame kit Not suitable: Nazgul Evoque F5 Nazgul Evoque F6 Packing List: 1 x BLITZ E55R 4-IN-1 2-6S ESC 1 x Power cables & ESC signal wires Description The next generation of ESCs from iFlight has arrived. These new 55Amp BLHeli32 BLITZ 4in1 ESCs can handle even the most amp-hungry motors. Lager Mosfets and bigger PCB for maximum heat dissipation. Powerful 55A for 2-6S batteries and 20x20 mounting pattern. The perfect match for the BLITZ Flight Controller series. Features: Larger MOSFET for more durable Better heat dissipation Safer with high redundancy Outstanding performance Specifications: Product Name: BLITZ E55R 4-IN-1 ESC (G2) Input Voltage: 2-6S Max. Continuous Current: 55A Max. Burst Current: 65A MCU: G071 BEC: No Firmware: BLHeli32 Current Sensor: Yes Current rate: 200 Telemetry: Supported Target: IFLIGHT_BLITZ_G2 Mounting Holes: 20 x20 mm/Φ4mm Weight: 15.3g Protocol: Supports DShot150/300/600/MultiShot/ OneShot etc. Compatibility: Mach R5 V1/Sport Frame kit AOS 5R Frame kit Not suitable: Nazgul Evoque F5 Nazgul Evoque F6 Packing List: 1 x BLITZ E55R 4-IN-1 2-6S ESC 1 x Power cables & ESC signal wires -
About Description The next generation of ESCs from iFlight has arrived. Currently also used in some of our BNF quads. These new 55Amp Bluejay or BLHeliS BLITZ 4in1 ESCs can handle even the most amp-hungry motors. Powerful 55A for 2-6S batteries. 30,5x30,5 mounting pattern. The perfect match for the BLITZ Flight Controller series. Specifications: Mounting Holes: 30.5*30.5mm/Φ4mm Weight: 14.7g Supports 2-6S lipo input MCU: BB21 Constant: 55 Amps Burst: 65 Amps Current sensor: Yes BEC: No Current rate: 200 Supports: DShot DShot150/300/600/MultiShot/ OneShot etc. Target: Q-H-25 16.7(BlheliS) / Bluejay Q-H-25 (Bluejay) Packing List: 1 x BLITZ E55S 4-IN-1 2-6S ESC 1 x Power cables & ESC signal wires Description The next generation of ESCs from iFlight has arrived. Currently also used in some of our BNF quads. These new 55Amp Bluejay or BLHeliS BLITZ 4in1 ESCs can handle even the most amp-hungry motors. Powerful 55A for 2-6S batteries. 30,5x30,5 mounting pattern. The perfect match for the BLITZ Flight Controller series. Specifications: Mounting Holes: 30.5*30.5mm/Φ4mm Weight: 14.7g Supports 2-6S lipo input MCU: BB21 Constant: 55 Amps Burst: 65 Amps Current sensor: Yes BEC: No Current rate: 200 Supports: DShot DShot150/300/600/MultiShot/ OneShot etc. Target: Q-H-25 16.7(BlheliS) / Bluejay Q-H-25 (Bluejay) Packing List: 1 x BLITZ E55S 4-IN-1 2-6S ESC 1 x Power cables & ESC signal wires -
About Description The MOSFET used by BLITZ E80 is PSMN1R0-40YLD, which can withstand a continuous current of 80A at 25°C, with a maximum power dissipation of 198W. BEC power supply adopts TI automotive-grade dedicated synchronous rectifier chip, supporting up to 100V.The 1-4 layer power board of the PCB circuit is ultra-thick copper with a thickness of 4OZ, ensuring continuous output under high-power operation. The STM32F051 main control processor with a running frequency of up to 48MHz, combined with a three-in-one driver IC, achieves a faster running speed! Highlights: Rational layout, countersunk holes on extended solder pads to ensure PCB layer connection G071 MCU, 48mHz maximum clock speed; TDK MLCC Low ESR ceramic capacitors; Top grade PSMN1R0-40YLD MOSFET; 8 layers double-sided PCB board Specifications: Product Name: BLITZ E80 4-IN-1 ESC Input Voltage: 2-8S Max. Continuous Current: 80A Max. Burst Current: 100A MCU: G071 BEC: No Firmware: BLHeli32 Current Sensor: Yes Telemetry: Supported Target: IFLIGHT_BLITZ_G2 Mounting Dimensions: 35x35mm/Φ3mm Dimensions: 35x42mm Weight: 65g(±10) Protocal: Supports DShot DShot150/300/600/MultiShot/ OneShot etc Packing List: 1 x BLITZ E80 4-IN-1 Pro ESC (G2） 1 x Wiring set Wiring Diagram https://drive.google.com/drive/folders/1l10mEOXwERfLqRun0bbHMEJoxXV2RKN2 Note: If you want to use it for the Taurus X8 V3, Protek60 Pro, X413, or X415 frame kit, please select the "Without CNC" option. BLHeliSuite download (BL32): https://github.com/blheli-configurator/blheli-configurator/releases Description The MOSFET used by BLITZ E80 is PSMN1R0-40YLD, which can withstand a continuous current of 80A at 25°C, with a maximum power dissipation of 198W. BEC power supply adopts TI automotive-grade dedicated synchronous rectifier chip, supporting up to 100V.The 1-4 layer power board of the PCB circuit is ultra-thick copper with a thickness of 4OZ, ensuring continuous output under high-power operation. The STM32F051 main control processor with a running frequency of up to 48MHz, combined with a three-in-one driver IC, achieves a faster running speed! Highlights: Rational layout, countersunk holes on extended solder pads to ensure PCB layer connection G071 MCU, 48mHz maximum clock speed; TDK MLCC Low ESR ceramic capacitors; Top grade PSMN1R0-40YLD MOSFET; 8 layers double-sided PCB board Specifications: Product Name: BLITZ E80 4-IN-1 ESC Input Voltage: 2-8S Max. Continuous Current: 80A Max. Burst Current: 100A MCU: G071 BEC: No Firmware: BLHeli32 Current Sensor: Yes Telemetry: Supported Target: IFLIGHT_BLITZ_G2 Mounting Dimensions: 35x35mm/Φ3mm Dimensions: 35x42mm Weight: 65g(±10) Protocal: Supports DShot DShot150/300/600/MultiShot/ OneShot etc Packing List: 1 x BLITZ E80 4-IN-1 Pro ESC (G2） 1 x Wiring set Wiring Diagram https://drive.google.com/drive/folders/1l10mEOXwERfLqRun0bbHMEJoxXV2RKN2 Note: If you want to use it for the Taurus X8 V3, Protek60 Pro, X413, or X415 frame kit, please select the "Without CNC" option. BLHeliSuite download (BL32): https://github.com/blheli-configurator/blheli-configurator/releases -
About Description BLITZ E80 BLHeli Dshot600 Single ESC was designed to give your motors smooth power with great stability and durability. The 32bit 48mHz G071 MCU and 11 pieces TDK MLCC total 240UF Low ESR capacitors bring faster responding speed and a smoother flying experience. Highlights 2-8S input (max 8S) 80A 8 layers 4OZ copper PCB, better operating load capacity; 11 pieces TDK MLCC total 420UF Low ESR capacitors, lower ripple and more stable; Top grade NTMFS5C430NL MOSFET, stable and reliable; 1 * 3528 LED for power- on display; Rational layout, large soldering pad, countersinks and semicircle orifices enable each layer to be energized after power-on. Specifications Product Name: BLITZ E80 Single ESC Input Voltage: 2-8S Max. Continuous Current: 80A Max. Burst Current: 100A MCU: G071 BEC: No Firmware: BLHeli32 Current Sensor: Yes Telemetry: Supported Target: IFLIGHT_BLITZ_G2 Dimensions: L40 x W17 x W10mm Weight: 14.5g(±2) Protocal: DShot DShot150/300/600/MultiShot/OneShot PWM Drive Supports Current Sensor Telemetry output Motor Timing Brake on Stop Packing List 1 x BLITZ E80 Single ESC 1 x 50V 470UF capacitor 1 x Power cables & ESC signal wires Wiring Diagram https://drive.google.com/drive/folders/1l10mEOXwERfLqRun0bbHMEJoxXV2RKN2 Description BLITZ E80 BLHeli Dshot600 Single ESC was designed to give your motors smooth power with great stability and durability. The 32bit 48mHz G071 MCU and 11 pieces TDK MLCC total 240UF Low ESR capacitors bring faster responding speed and a smoother flying experience. Highlights 2-8S input (max 8S) 80A 8 layers 4OZ copper PCB, better operating load capacity; 11 pieces TDK MLCC total 420UF Low ESR capacitors, lower ripple and more stable; Top grade NTMFS5C430NL MOSFET, stable and reliable; 1 * 3528 LED for power- on display; Rational layout, large soldering pad, countersinks and semicircle orifices enable each layer to be energized after power-on. Specifications Product Name: BLITZ E80 Single ESC Input Voltage: 2-8S Max. Continuous Current: 80A Max. Burst Current: 100A MCU: G071 BEC: No Firmware: BLHeli32 Current Sensor: Yes Telemetry: Supported Target: IFLIGHT_BLITZ_G2 Dimensions: L40 x W17 x W10mm Weight: 14.5g(±2) Protocal: DShot DShot150/300/600/MultiShot/OneShot PWM Drive Supports Current Sensor Telemetry output Motor Timing Brake on Stop Packing List 1 x BLITZ E80 Single ESC 1 x 50V 470UF capacitor 1 x Power cables & ESC signal wires Wiring Diagram https://drive.google.com/drive/folders/1l10mEOXwERfLqRun0bbHMEJoxXV2RKN2 -
About Description BLITZ E80 BLHeli Dshot600 Single ESC was designed to give your motors smooth power with great stability and durability. The 32bit 48mHz G071 MCU and 11 pieces TDK MLCC total 240UF Low ESR capacitors bring faster responding speed and a smoother flying experience. Features Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required) FC indicator LEDs for visual debugging BLITZ E80 BLHeli Dshot600 Single ESC was designed to give your motors smooth power with great stability and durability. The 32bit 48mHz G071 MCU and 11 pieces TDK MLCC total 240UF Low ESR capacitors bring faster responding speed and a smoother flying experience. FC Specifications Product Name: BLITZ F7 Pro Flight Controller Mount pattern: 35*35mm/ 4mm PCB hole diameter Smartaudio / IRC Tramp VTX protocol supported Firmware target: IFLIGHT_BLITZ_F7_PRO Input Voltage: 14.8V-34V (4S-8S LIPO) Motor outputs: 4x (SH1.25 connector) Flash: 512MB (Blackbox flash) I2C serial: SDA / SLA pads Dimensions: 41*41.5mm Barometer: DPS310 OSD Chip: AT7456E LED controller: Yes MCU: STM32 F722 Weight: 17g (±2) Beeper pad: Yes Gyro: BMI270 UARTS: 4 ESC Specifications Product Name: BLITZ E80 Single ESC Input Voltage: 2-8S Max. Continuous Current: 80A Max. Burst Current: 100A MCU: G071 BEC: No Firmware: BLHeli32 Current Sensor: Yes Telemetry: Supported Target: IFLIGHT_BLITZ_G2 Dimensions: L40 x W17 x W10mm Weight: 14.5g(±2) Protocal: DShot DShot150/300/600/MultiShot/OneShot PWM Drive Packing List 1 x BLITZ F7 Pro Flight Controller 8 x BLITZ E80 Single ESC with CNC Alum Cover（Combo1） 8 x 50V 470UF capacitor（Combo1） 8 x Power cables & ESC signal wires（Combo1） 2 x BLITZ Pro PDB（Combo1） 4 x BLITZ E80 Single ESC with CNC Alum Cover（Combo2） 4 x 50V 470UF capacitor（Combo2） 4 x Power cables & ESC signal wires（Combo2） 1 x BLITZ Pro PDB 1 x Screws Pack 1 x USB Adapter Board Wiring Diagrams https://drive.google.com/drive/folders/17Uf67I6ER_z-otviR0I7tSqO31W7S553 https://drive.google.com/drive/folders/1l10mEOXwERfLqRun0bbHMEJoxXV2RKN2 Description BLITZ E80 BLHeli Dshot600 Single ESC was designed to give your motors smooth power with great stability and durability. The 32bit 48mHz G071 MCU and 11 pieces TDK MLCC total 240UF Low ESR capacitors bring faster responding speed and a smoother flying experience. Features Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required) FC indicator LEDs for visual debugging BLITZ E80 BLHeli Dshot600 Single ESC was designed to give your motors smooth power with great stability and durability. The 32bit 48mHz G071 MCU and 11 pieces TDK MLCC total 240UF Low ESR capacitors bring faster responding speed and a smoother flying experience. FC Specifications Product Name: BLITZ F7 Pro Flight Controller Mount pattern: 35*35mm/ 4mm PCB hole diameter Smartaudio / IRC Tramp VTX protocol supported Firmware target: IFLIGHT_BLITZ_F7_PRO Input Voltage: 14.8V-34V (4S-8S LIPO) Motor outputs: 4x (SH1.25 connector) Flash: 512MB (Blackbox flash) I2C serial: SDA / SLA pads Dimensions: 41*41.5mm Barometer: DPS310 OSD Chip: AT7456E LED controller: Yes MCU: STM32 F722 Weight: 17g (±2) Beeper pad: Yes Gyro: BMI270 UARTS: 4 ESC Specifications Product Name: BLITZ E80 Single ESC Input Voltage: 2-8S Max. Continuous Current: 80A Max. Burst Current: 100A MCU: G071 BEC: No Firmware: BLHeli32 Current Sensor: Yes Telemetry: Supported Target: IFLIGHT_BLITZ_G2 Dimensions: L40 x W17 x W10mm Weight: 14.5g(±2) Protocal: DShot DShot150/300/600/MultiShot/OneShot PWM Drive Packing List 1 x BLITZ F7 Pro Flight Controller 8 x BLITZ E80 Single ESC with CNC Alum Cover（Combo1） 8 x 50V 470UF capacitor（Combo1） 8 x Power cables & ESC signal wires（Combo1） 2 x BLITZ Pro PDB（Combo1） 4 x BLITZ E80 Single ESC with CNC Alum Cover（Combo2） 4 x 50V 470UF capacitor（Combo2） 4 x Power cables & ESC signal wires（Combo2） 1 x BLITZ Pro PDB 1 x Screws Pack 1 x USB Adapter Board Wiring Diagrams https://drive.google.com/drive/folders/17Uf67I6ER_z-otviR0I7tSqO31W7S553 https://drive.google.com/drive/folders/1l10mEOXwERfLqRun0bbHMEJoxXV2RKN2 -
About Description Our latest BLITZ Stack used in our iFlight BNFs. Ultra fast F7 MCU, powerful 55A for 2-6S batteries. 30,5x30,5 mounting pattern. The perfect match for your new frame. Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required), FC indicator LEDs for visual debugging, with LC filter. FC Specifications: MCU: STM32 F722 Gyro: ICM42688 Barometer: DPS310 OSD Chip: AT7456E Flash: 32MB (Blackbox flash) UARTS: 6 Motor outputs: 4x (SH1.0 connector) I2C serial: SDA / SLA pads Smartaudio / IRC Tramp VTX protocol supported LED controller: Yes Beeper pad: Yes Firmware target: IFRC-IFLIGHT_BLITZ_F722 Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter Dimensions: 36.5*35 mm Weight: 7.8g BEC: 5V 2.5A / 9V 2A Wiring Suggestions: UART 1 for VTX HD / Analog UART 2 for a Receiver UART 3/4/5 for GPS or other sensors that require a serial port UART 6 for ESC Telemetry ESC Specifications Mounting Holes: 30.5*30.5mm/Φ4mm Weight: 15.3g Supports 2-6S lipo input MCU: G071 Constant: 55 Amps Burst: 65 Amps Current sensor: Yes BEC: No Current rate: 200 Supports: DShot DShot150/300/600/MultiShot/ OneShot etc. Target: IFLIGHT_BLITZ_G3 32.9 Packing List: 1 x BLITZ F7 V1.2 Flight Controller 1 x BLITZ E55 4-IN-1 2-6S ESC 1 x silicon grommets 1 x wire harness for F7 Flight controller Description Our latest BLITZ Stack used in our iFlight BNFs. Ultra fast F7 MCU, powerful 55A for 2-6S batteries. 30,5x30,5 mounting pattern. The perfect match for your new frame. Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required), FC indicator LEDs for visual debugging, with LC filter. FC Specifications: MCU: STM32 F722 Gyro: ICM42688 Barometer: DPS310 OSD Chip: AT7456E Flash: 32MB (Blackbox flash) UARTS: 6 Motor outputs: 4x (SH1.0 connector) I2C serial: SDA / SLA pads Smartaudio / IRC Tramp VTX protocol supported LED controller: Yes Beeper pad: Yes Firmware target: IFRC-IFLIGHT_BLITZ_F722 Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter Dimensions: 36.5*35 mm Weight: 7.8g BEC: 5V 2.5A / 9V 2A Wiring Suggestions: UART 1 for VTX HD / Analog UART 2 for a Receiver UART 3/4/5 for GPS or other sensors that require a serial port UART 6 for ESC Telemetry ESC Specifications Mounting Holes: 30.5*30.5mm/Φ4mm Weight: 15.3g Supports 2-6S lipo input MCU: G071 Constant: 55 Amps Burst: 65 Amps Current sensor: Yes BEC: No Current rate: 200 Supports: DShot DShot150/300/600/MultiShot/ OneShot etc. Target: IFLIGHT_BLITZ_G3 32.9 Packing List: 1 x BLITZ F7 V1.2 Flight Controller 1 x BLITZ E55 4-IN-1 2-6S ESC 1 x silicon grommets 1 x wire harness for F7 Flight controller -
About Description Our latest BLITZ Flight Controller used in our iFlight BNFs. Ultra fast F7 MCU for 2-6S batteries. 30,5x30,5 mounting pattern. The perfect match for your new frame. Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required), FC indicator LEDs for visual debugging, with LC filter. Description Our latest BLITZ Flight Controller used in our iFlight BNFs. Ultra fast F7 MCU for 2-6S batteries. 30,5x30,5 mounting pattern. The perfect match for your new frame. Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required), FC indicator LEDs for visual debugging, with LC filter. -
About Description Our latest BLITZ Flight Controller used in our iFlight BNFs. Ultra fast F7 MCU for 2-6S batteries. 30,5x30,5 mounting pattern. The perfect match for your new frame. Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required), FC indicator LEDs for visual debugging, with LC filter. Specifications: MCU: STM32 F722 Gyro: ICM42688 Barometer: DPS310 OSD Chip: AT7456E Flash: 32MB (Blackbox flash) UARTS: 6 Motor outputs: 4x (SH1.0 connector) I2C serial: SDA / SLA pads Smartaudio / IRC Tramp VTX protocol supported LED controller: Yes Beeper pad: Yes Firmware target: IFRC-IFLIGHT_BLITZ_F722 Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter Dimensions: 36.5*35 mm Weight: 7.8g BEC: 5V 2.5A / 9V 2A Wiring Suggestion: UART 1 for VTX HD / Analog UART 2 for a Receiver UART 3/4/5 for GPS or other sensors that require a serial port UART 6 for ESC Telemet Packing List: 1 x BLITZ F7 V1.2 Flight Controller 1 x FC connectors (as above) 1 x silicon grommets Description Our latest BLITZ Flight Controller used in our iFlight BNFs. Ultra fast F7 MCU for 2-6S batteries. 30,5x30,5 mounting pattern. The perfect match for your new frame. Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required), FC indicator LEDs for visual debugging, with LC filter. Specifications: MCU: STM32 F722 Gyro: ICM42688 Barometer: DPS310 OSD Chip: AT7456E Flash: 32MB (Blackbox flash) UARTS: 6 Motor outputs: 4x (SH1.0 connector) I2C serial: SDA / SLA pads Smartaudio / IRC Tramp VTX protocol supported LED controller: Yes Beeper pad: Yes Firmware target: IFRC-IFLIGHT_BLITZ_F722 Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter Dimensions: 36.5*35 mm Weight: 7.8g BEC: 5V 2.5A / 9V 2A Wiring Suggestion: UART 1 for VTX HD / Analog UART 2 for a Receiver UART 3/4/5 for GPS or other sensors that require a serial port UART 6 for ESC Telemet Packing List: 1 x BLITZ F7 V1.2 Flight Controller 1 x FC connectors (as above) 1 x silicon grommets -
About Description Our latest BLITZ FC used in our iFlight BNFs. Ultra fast F7 MCU with 30,5x30,5 mounting pattern. The perfect match for your new frame. Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required), FC indicator LEDs for visual debugging, with LC filter. Features: Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required) FC indicator LEDs for visual debugging Support Betaflight, INAV, Ardupilot firmware FC Specifications: MCU: STM32F745 Gyro: ICM42688 Barometer: DPS310 OSD Chip: AT7456E Flash: 32MB (Blackbox flash) UARTS: 6 Smartaudio / IRC Tramp VTX protocol supported LED controller: Yes Beeper pad: Yes Mount pattern: 30.5*30.5mm Dimensions: 36.5*35 mm Weight: 7.8g BEC: 5V 2.5A / 9V 2A BF Firmware target: IFLIGHT_BLITZ_F7_AIO Ardupilot Firmware：arduplane_with_bl Wiring Suggestions: UART 1 for VTX HD / Analog UART 2 for a Receiver UART 3/4/5 for GPS or other sensors that require a serial port UART 6 for ESC Telemetry Packing List: 1 x BLITZ F745 Flight Controller Wiring Diagram: https://drive.google.com/drive/u/1/folders/17Uf67I6ER_z-otviR0I7tSqO31W7S553 Note: Please use our GoogleDrive Database to download the Ardupilot firmware of the FC： https://drive.google.com/drive/folders/1r3MNTBNYSzGeRXQg45j4IJVoW1Xjk7Y0 Description Our latest BLITZ FC used in our iFlight BNFs. Ultra fast F7 MCU with 30,5x30,5 mounting pattern. The perfect match for your new frame. Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required), FC indicator LEDs for visual debugging, with LC filter. Features: Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required) FC indicator LEDs for visual debugging Support Betaflight, INAV, Ardupilot firmware FC Specifications: MCU: STM32F745 Gyro: ICM42688 Barometer: DPS310 OSD Chip: AT7456E Flash: 32MB (Blackbox flash) UARTS: 6 Smartaudio / IRC Tramp VTX protocol supported LED controller: Yes Beeper pad: Yes Mount pattern: 30.5*30.5mm Dimensions: 36.5*35 mm Weight: 7.8g BEC: 5V 2.5A / 9V 2A BF Firmware target: IFLIGHT_BLITZ_F7_AIO Ardupilot Firmware：arduplane_with_bl Wiring Suggestions: UART 1 for VTX HD / Analog UART 2 for a Receiver UART 3/4/5 for GPS or other sensors that require a serial port UART 6 for ESC Telemetry Packing List: 1 x BLITZ F745 Flight Controller Wiring Diagram: https://drive.google.com/drive/u/1/folders/17Uf67I6ER_z-otviR0I7tSqO31W7S553 Note: Please use our GoogleDrive Database to download the Ardupilot firmware of the FC： https://drive.google.com/drive/folders/1r3MNTBNYSzGeRXQg45j4IJVoW1Xjk7Y0 -
About Description Our latest BLITZ Stack used in our iFlight BNFs. Ultra fast F7 MCU, powerful 55A for 2-6S batteries. 30,5x30,5 mounting pattern. The perfect match for your new frame. Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required), FC indicator LEDs for visual debugging, with LC filter. FC Specifications: MCU: STM32F745 Gyro: ICM42688 Barometer: DPS310 OSD Chip: AT7456E Flash: 32MB (Blackbox flash) UARTS: 6 Smartaudio / IRC Tramp VTX protocol supported LED controller: Yes Beeper pad: Yes Mount pattern: 30.5*30.5mm Dimensions: 36.5*35 mm Weight: 7.8g BEC: 5V 2.5A / 9V 2A BF Firmware target: IFLIGHT_BLITZ_F7_AIO Ardupilot Firmware：arduplane_with_bl Wiring Suggestions: UART 1 for VTX HD / Analog UART 2 for a Receiver UART 3/4/5 for GPS or other sensors that require a serial port UART 6 for ESC Telemetry ESC Specifications: Mounting Holes: 30.5*30.5mm/Φ4mm Weight: 15.3g Supports 2-6S lipo input MCU: G071 Constant: 55 Amps Burst: 65 Amps Current sensor: Yes BEC: No Current rate: 200 Supports: DShot DShot150/300/600/MultiShot/ OneShot etc. Target: IFLIGHT_BLITZ_G3 32.9 Packing List: 1 x BLITZ F745 V1.2 Flight Controller 1 x BLITZ E55 4-IN-1 2-6S ESC 1 x silicon grommets 1 x wire harness for F7 Flight controller Wiring Diagram: https://drive.google.com/drive/u/1/folders/17Uf67I6ER_z-otviR0I7tSqO31W7S553 Note: Please use our GoogleDrive Database to download the Ardupilot firmware of the FC： https://drive.google.com/drive/folders/1r3MNTBNYSzGeRXQg45j4IJVoW1Xjk7Y0 Description Our latest BLITZ Stack used in our iFlight BNFs. Ultra fast F7 MCU, powerful 55A for 2-6S batteries. 30,5x30,5 mounting pattern. The perfect match for your new frame. Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required), FC indicator LEDs for visual debugging, with LC filter. FC Specifications: MCU: STM32F745 Gyro: ICM42688 Barometer: DPS310 OSD Chip: AT7456E Flash: 32MB (Blackbox flash) UARTS: 6 Smartaudio / IRC Tramp VTX protocol supported LED controller: Yes Beeper pad: Yes Mount pattern: 30.5*30.5mm Dimensions: 36.5*35 mm Weight: 7.8g BEC: 5V 2.5A / 9V 2A BF Firmware target: IFLIGHT_BLITZ_F7_AIO Ardupilot Firmware：arduplane_with_bl Wiring Suggestions: UART 1 for VTX HD / Analog UART 2 for a Receiver UART 3/4/5 for GPS or other sensors that require a serial port UART 6 for ESC Telemetry ESC Specifications: Mounting Holes: 30.5*30.5mm/Φ4mm Weight: 15.3g Supports 2-6S lipo input MCU: G071 Constant: 55 Amps Burst: 65 Amps Current sensor: Yes BEC: No Current rate: 200 Supports: DShot DShot150/300/600/MultiShot/ OneShot etc. Target: IFLIGHT_BLITZ_G3 32.9 Packing List: 1 x BLITZ F745 V1.2 Flight Controller 1 x BLITZ E55 4-IN-1 2-6S ESC 1 x silicon grommets 1 x wire harness for F7 Flight controller Wiring Diagram: https://drive.google.com/drive/u/1/folders/17Uf67I6ER_z-otviR0I7tSqO31W7S553 Note: Please use our GoogleDrive Database to download the Ardupilot firmware of the FC： https://drive.google.com/drive/folders/1r3MNTBNYSzGeRXQg45j4IJVoW1Xjk7Y0 -
About Description The newly upgraded BLITZ M10 GPS V2 has arrived, offering faster and more stable satellite search. This advancement in technology provides users with a more reliable and efficient GPS experience. Features: UBLOX M10 chip, low power consumption, strong signal Compass module QMC5883L integrated Built-in farad capacitor for faster hot start High-precision positioning Onboard LNA (Low Noise Amplifier), RF filter, and TCXO (temperature-compensated crystal oscillator) 10 Hz Refresh rate Built-in Flash Specifications: Compass module: QMC5883L Baud Rate: 9600-460800 / 4800bps-921600bps (Default - 115200bps) Sensitivity: Tracking: -167dBm Cold start: 27s Hot start: 1s Maximum height: 80000m Maximum speed: 500 m/s Speed accuracy: 0.05 m/s Maximum acceleration: ≦ 4G Refresh Rate: 10 Hz GPS patch antenna size: 18.2 x 18.2 x 4 mm / 25 x 25 x 6 mm Total dimensions: 20 x 21 x 8 mm / 25 x 25 x 11 mm Weight: 8g / 16 g Input Voltage: 3.3-5.5 V GPS pin definition: RX/TX UART Compass pin definition: SDA/SLA GNSS: GPS+SBAS+Galileo+QZSS+Glonass Compatibility: 25*25*6 Version Centurion X8 Frame Kit Packing List: 1 x BLITZ M10 GPS V2 1 x Cable set Description The newly upgraded BLITZ M10 GPS V2 has arrived, offering faster and more stable satellite search. This advancement in technology provides users with a more reliable and efficient GPS experience. Features: UBLOX M10 chip, low power consumption, strong signal Compass module QMC5883L integrated Built-in farad capacitor for faster hot start High-precision positioning Onboard LNA (Low Noise Amplifier), RF filter, and TCXO (temperature-compensated crystal oscillator) 10 Hz Refresh rate Built-in Flash Specifications: Compass module: QMC5883L Baud Rate: 9600-460800 / 4800bps-921600bps (Default - 115200bps) Sensitivity: Tracking: -167dBm Cold start: 27s Hot start: 1s Maximum height: 80000m Maximum speed: 500 m/s Speed accuracy: 0.05 m/s Maximum acceleration: ≦ 4G Refresh Rate: 10 Hz GPS patch antenna size: 18.2 x 18.2 x 4 mm / 25 x 25 x 6 mm Total dimensions: 20 x 21 x 8 mm / 25 x 25 x 11 mm Weight: 8g / 16 g Input Voltage: 3.3-5.5 V GPS pin definition: RX/TX UART Compass pin definition: SDA/SLA GNSS: GPS+SBAS+Galileo+QZSS+Glonass Compatibility: 25*25*6 Version Centurion X8 Frame Kit Packing List: 1 x BLITZ M10 GPS V2 1 x Cable set -
About Description The newly upgraded BLITZ M10 GPS V2 has arrived, offering faster and more stable satellite search. This advancement in technology provides users with a more reliable and efficient GPS experience. Features: UBLOX M10 chip, low power consumption, strong signal Compass module QMC5883L integrated Built-in farad capacitor for faster hot start High-precision positioning Onboard LNA (Low Noise Amplifier), RF filter, and TCXO (temperature-compensated crystal oscillator) 10 Hz Refresh rate Built-in Flash Specifications: Compass module: QMC5883L Baud Rate: 9600-460800 / 4800bps-921600bps (Default - 115200bps) Sensitivity: Tracking: -167dBm Cold start: 27s Hot start: 1s Maximum height: 80000m Maximum speed: 500 m/s Speed accuracy: 0.05 m/s Maximum acceleration: ≦ 4G Refresh Rate: 10 Hz GPS patch antenna size: 18.2 x 18.2 x 4 mm / 25 x 25 x 6 mm Total dimensions: 20 x 21 x 8 mm / 25 x 25 x 11 mm Weight: 8g / 16 g Input Voltage: 3.3-5.5 V GPS pin definition: RX/TX UART Compass pin definition: SDA/SLA GNSS: GPS+SBAS+Galileo+QZSS+Glonass Compatibility: 20*21*8(Mini Version) Single-hole TPU mount: Chimera7 Pro v2 iH3 O3 Nazgul Evoque F4/F5/F6 XL10 v6 BOB57 HD Dual hole TPU mount: Nazgul5 V3 Taurus X8 Pro/V3 ProTek60 Pro Packing List: 1 x BLITZ M10 GPS V2 1 x Cable set Description The newly upgraded BLITZ M10 GPS V2 has arrived, offering faster and more stable satellite search. This advancement in technology provides users with a more reliable and efficient GPS experience. Features: UBLOX M10 chip, low power consumption, strong signal Compass module QMC5883L integrated Built-in farad capacitor for faster hot start High-precision positioning Onboard LNA (Low Noise Amplifier), RF filter, and TCXO (temperature-compensated crystal oscillator) 10 Hz Refresh rate Built-in Flash Specifications: Compass module: QMC5883L Baud Rate: 9600-460800 / 4800bps-921600bps (Default - 115200bps) Sensitivity: Tracking: -167dBm Cold start: 27s Hot start: 1s Maximum height: 80000m Maximum speed: 500 m/s Speed accuracy: 0.05 m/s Maximum acceleration: ≦ 4G Refresh Rate: 10 Hz GPS patch antenna size: 18.2 x 18.2 x 4 mm / 25 x 25 x 6 mm Total dimensions: 20 x 21 x 8 mm / 25 x 25 x 11 mm Weight: 8g / 16 g Input Voltage: 3.3-5.5 V GPS pin definition: RX/TX UART Compass pin definition: SDA/SLA GNSS: GPS+SBAS+Galileo+QZSS+Glonass Compatibility: 20*21*8(Mini Version) Single-hole TPU mount: Chimera7 Pro v2 iH3 O3 Nazgul Evoque F4/F5/F6 XL10 v6 BOB57 HD Dual hole TPU mount: Nazgul5 V3 Taurus X8 Pro/V3 ProTek60 Pro Packing List: 1 x BLITZ M10 GPS V2 1 x Cable set -
About Description Our latest BLITZ Flight Controller used in our iFlight BNFs. Ultra fast ATF435 MCU for 2-6S batteries. 20x20 mounting pattern. The perfect match for your new frame. Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required), FC indicator LEDs for visual debugging, with LC filter. Specifications: MCU: AT32F435RGT7 Gyro: BMI270 Barometer: DPS310 OSD Chip: AT7456E Flash: 16MB (Blackbox flash) UARTS: 6 Motor outputs: 4x (SH1.0 connector) I2C serial: SDA / SLA pads Smartaudio / IRC Tramp VTX protocol supported LED controller: Yes Beeper pad: Yes Firmware target: IFLIGHT_BLITZ_ATF435 Mount pattern: 20*20mm/φ4 Dimensions: 30.5*27mm Weight: 5g BEC: 5V 2.5A Wiring Suggestion: UART 1 for VTX HD / Analog UART 2 for a Receiver UART 3/4/5 for GPS or other sensors that require a serial port UART 6 for ESC Telemet Packing List: 1 x BLITZ Mini ATF435 Flight Controller Description Our latest BLITZ Flight Controller used in our iFlight BNFs. Ultra fast ATF435 MCU for 2-6S batteries. 20x20 mounting pattern. The perfect match for your new frame. Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required), FC indicator LEDs for visual debugging, with LC filter. Specifications: MCU: AT32F435RGT7 Gyro: BMI270 Barometer: DPS310 OSD Chip: AT7456E Flash: 16MB (Blackbox flash) UARTS: 6 Motor outputs: 4x (SH1.0 connector) I2C serial: SDA / SLA pads Smartaudio / IRC Tramp VTX protocol supported LED controller: Yes Beeper pad: Yes Firmware target: IFLIGHT_BLITZ_ATF435 Mount pattern: 20*20mm/φ4 Dimensions: 30.5*27mm Weight: 5g BEC: 5V 2.5A Wiring Suggestion: UART 1 for VTX HD / Analog UART 2 for a Receiver UART 3/4/5 for GPS or other sensors that require a serial port UART 6 for ESC Telemet Packing List: 1 x BLITZ Mini ATF435 Flight Controller -
About Description Our latest BLITZ Stack used in our iFlight BNFs. Ultra fast AT32F435 MCU, powerful 55A for 2-6S batteries. 20x20 mounting pattern. The perfect match for your new frame. Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required), FC indicator LEDs for visual debugging, with LC filter. FC Specifications: MCU: AT32F435RGT7 Gyro: BMI270 Barometer: DPS310 OSD Chip: AT7456E Flash: 16MB (Blackbox flash) UARTS: 6 Motor outputs: 4x (SH1.0 connector) I2C serial: SDA / SLA pads Smartaudio / IRC Tramp VTX protocol supported LED controller: Yes Beeper pad: Yes Firmware target: IFLIGHT_BLITZ_ATF435 Mount pattern: 20*20mm/φ4 Dimensions: 30.5*27mm Weight: 5g BEC: 5V 2.5A ESC Specifications: Mounting Holes: 20*20mm/Φ4mm Weight: 11.3g Supports 2-6S lipo input MCU: BB21 Constant: 55 Amps Burst: 65 Amps Telemetry Output: No Current sensor: Yes Current rate: 200 BEC: No Supports: DShot DShot150/300/600/MultiShot/ OneShot etc. Target: Q-H-25 16.7(BlheliS) / Bluejay Q-H-50 (Bluejay) Packing List: 1 x BLITZ Mini ATF435 Flight Controller 1 x BLITZ Mini E55S 4-IN-1 2-6S ESC 1 x Power cables & ESC signal wires Description Our latest BLITZ Stack used in our iFlight BNFs. Ultra fast AT32F435 MCU, powerful 55A for 2-6S batteries. 20x20 mounting pattern. The perfect match for your new frame. Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required), FC indicator LEDs for visual debugging, with LC filter. FC Specifications: MCU: AT32F435RGT7 Gyro: BMI270 Barometer: DPS310 OSD Chip: AT7456E Flash: 16MB (Blackbox flash) UARTS: 6 Motor outputs: 4x (SH1.0 connector) I2C serial: SDA / SLA pads Smartaudio / IRC Tramp VTX protocol supported LED controller: Yes Beeper pad: Yes Firmware target: IFLIGHT_BLITZ_ATF435 Mount pattern: 20*20mm/φ4 Dimensions: 30.5*27mm Weight: 5g BEC: 5V 2.5A ESC Specifications: Mounting Holes: 20*20mm/Φ4mm Weight: 11.3g Supports 2-6S lipo input MCU: BB21 Constant: 55 Amps Burst: 65 Amps Telemetry Output: No Current sensor: Yes Current rate: 200 BEC: No Supports: DShot DShot150/300/600/MultiShot/ OneShot etc. Target: Q-H-25 16.7(BlheliS) / Bluejay Q-H-50 (Bluejay) Packing List: 1 x BLITZ Mini ATF435 Flight Controller 1 x BLITZ Mini E55S 4-IN-1 2-6S ESC 1 x Power cables & ESC signal wires -
About Description The next generation of ESCs from iFlight has arrived. Currently used in BNF quads such as the Nazgul F5/F6 Series. These new 55Amp BLHeli32 BLITZ Mini 4in1 ESCs can handle even the most amp-hungry motors. Powerful 55A for 2-6S batteries. 20x20 mounting pattern. The perfect match for the BLITZ Flight Controller series. Specifications: Product Name: BLITZ Mini E55 4-IN-1 ESC Input Voltage: 2-6S Max. Continuous Current: 55A Max. Burst Current: 65A MCU: G071 BEC: No Firmware: BLHeli32 Current Sensor: Yes Telemetry: Supported Target: IFLIGHT_BLITZ_G071_01 32.9 Mounting Dimensions: 20 x20 mm/Φ4mm Dimensions: 35x42mm Weight: 11.3g Protocol: Supports DShot DShot150/300/600/MultiShot/ OneShot etc Packing List: 1 x BLITZ Mini E55 4-IN-1 2-6S ESC 1 x Power cables & ESC signal wires Note: If you need to use the ESC in the iH3 O3 Frame kit, please remove the capacitor after receiving the ESC, and then install the ESC. Description The next generation of ESCs from iFlight has arrived. Currently used in BNF quads such as the Nazgul F5/F6 Series. These new 55Amp BLHeli32 BLITZ Mini 4in1 ESCs can handle even the most amp-hungry motors. Powerful 55A for 2-6S batteries. 20x20 mounting pattern. The perfect match for the BLITZ Flight Controller series. Specifications: Product Name: BLITZ Mini E55 4-IN-1 ESC Input Voltage: 2-6S Max. Continuous Current: 55A Max. Burst Current: 65A MCU: G071 BEC: No Firmware: BLHeli32 Current Sensor: Yes Telemetry: Supported Target: IFLIGHT_BLITZ_G071_01 32.9 Mounting Dimensions: 20 x20 mm/Φ4mm Dimensions: 35x42mm Weight: 11.3g Protocol: Supports DShot DShot150/300/600/MultiShot/ OneShot etc Packing List: 1 x BLITZ Mini E55 4-IN-1 2-6S ESC 1 x Power cables & ESC signal wires Note: If you need to use the ESC in the iH3 O3 Frame kit, please remove the capacitor after receiving the ESC, and then install the ESC.
Не забудьте запросить цитату наши цены вас очень удивят.Специальные цены при оптовой продаже.Мы занимаемся таможенными и транспортными процедурами.Доставка по адресу по всей России
Turkey